We share bonuses for online slots! Slots and Pokies are fun to play if you Cisco 3850 Reload Slot Command play sensibly and use reputable casinos. We believe playing pokies online is the best option, and that’s why we share the best online casino bonuses and even some sensible gambling advice. Some great places to get support if you feel you may have, or be in danger of developing. Router# Reload scheduled for 02:00:00 PDT Sat Apr 21 1996 (in 38 hours and 9 minutes) Proceed with reload? confirm The following example shows how to cancel a pending reload: Router# reload cancel. For more details on the Cisco Reload command and it's options, you can visit the Cisco documentation linked in the references below. To power off a particular module, use Switch(config)# no hw-module module num power; you can find that command on Page 20 of this Cisco doc. FYI, there isn't a graceful shutdown command for the whole switch. You should backup your config (just in case), issue a reboot, wait till you can audibly hear a change in fan speed, and then remove. The reason for the reload; this reason is stored in memory and is used for a show reload command, sending warning messages, or sending messages to syslog servers. Tells the router to reload some time from now. For example, to start a reload in two hours, enter in 2:00. At hh:mm month day. Tells the router to reload at a specific time (hh:mm).
CiscoルータやCatalystのreloadコマンドについて、構文や使い方を実行例交えて説明しています。
reloadコマンドを使うと、CiscoルータやCatalystを再起動出来ます。
再起動が必要な設定を行った場合や、IOSやIOS XEをアップデートした時等に使います。
時間を指定して再起動する事も出来ます。
尚、SUPが冗長化された機器で装置全体を再起動するためには、redundancy reload shelfコマンドを実行しなければいけない機種もあります。そのような機種でreloadコマンドを実行すると、アクティブ側のSUPだけ再起動されます。
reloadコマンドの構文は以下の通りです。
オプションを付けずに実行すると装置全体を再起動します。スタック構成の場合は、スタックを構成するスイッチ全てが再起動されます。
スタック構成時にslotオプションを指定すると、指定したスイッチだけ再起動する事が出来ます。
atを付けると再起動する月日や時間を指定出来ます。inは何時間何分後に再起動するかです。cancelはその取り消しです。
reloadコマンドの利用例は以下の通りです。
赤字の部分でrunning-configをstartup-configに保存するか書かれているため、yes or noで入力します。
緑色の部分は再起動して良いかの確認のため、そのままエンターキーを押します。
スタック構成でメンバーの1台だけ再起動する場合の利用例は以下の通りです。
上記でスタックメンバー番号3番のスイッチだけ再起動されます。
atオプションの利用例は以下の通りです。
その日の21:00に再起動されます。もし、21時を過ぎて指定すると次の日の21時に再起動されます。月日を指定する場合はreload at 21:00 Jan 3等になります。
inオプションの利用例は以下の通りです。
上記で10分後に再起動します。1:30と指定すると1時間30分後という意味になります。
設定した再起動を取り消す例は以下の通りです。
・特権EXECモード
・設定編「起動・停止・再起動」
CiscoルータやCatalystの起動、停止、再起動方法について説明しています。
・設定編「スタックの設定」
Catalystでスタックを構成する時の留意点や設定、確認方法について説明しています。
「Ciscoルータ/Catalystコマンド一覧」に戻る